Make it last, day after day.
Cleaning, materials, heat and travel: everything to keep your pill organizer in top condition, collection by collection. For regulatory information (manufacturer, EU authorised representative, safety warnings under the GPSR), see the GPSR compliance page.
For every model
Four rules, whatever your model.
These apply to every Biinii Design pill organizer. Each collection below only adds what is specific to it.
An organization aid, not a medical device
Our organizers hold dry pills, supplements and vitamins for short-term personal use. They do not replace a medical device. For long-term storage of sensitive medication, ask a healthcare professional and follow the leaflets of the products you place inside.
Heat is the one real enemy
Keep away from heat and direct sunlight. PLA softens from about 60 °C, PETG from about 80 °C, and may gradually change shape: a closed car in summer sun is enough. Not for microwave, oven or dishwasher.
Children and pets
Keep out of reach of children and pets to prevent access to the contents. Small models are a choking hazard; each collection below tells you which.
Storage and end of life
Store in a cool, dry place, away from sharp objects that could scratch the surface. Not watertight unless stated. At end of life, dispose of it according to your local recycling rules.
Collection
Daily.
One row, 2 to 4 compartments. Designed and 3D-printed in PLA, with a sliding lid that locks into two side notches, no magnets, no metal parts.
Browse daily pill organizersSpecific caution
- Compact models (2-compartment): choking hazard, small parts. Keep away from young children; do not put in the mouth or swallow.
Cleaning and care
- Rinse gently with lukewarm water and mild soap.
- Clean with a soft cloth; avoid abrasive cleaners and scouring pads.
- Avoid prolonged soaking. Dry thoroughly before refilling.
Collection
Travel.
Two rows, 4 to 8 compartments. Designed and 3D-printed in PLA. The photo organizer uses the same case, with your photo or logo UV-printed on its lid.
Browse travel pill organizersSpecific caution
- Not intended for liquids or leak-prone gel capsules.
- On the road: avoid the glovebox and the dashboard in summer, heat deforms PLA.
Flights and security
- 3D-printed plastic, no metal parts: goes through airport security without a fuss.
- For the medication itself, rules vary by country; when in doubt, travel with your prescription.
Cleaning and care
- Rinse gently with lukewarm water and mild soap.
- Clean with a soft cloth; avoid abrasive cleaners.
- Dry thoroughly before refilling, especially after a trip.
Collection
Weekly.
7-day and 8-compartment layouts in PLA: a magnetic lid you turn on the round model, a sliding lid that locks into two side notches on the compact model. The round model closes with neodymium magnets fully enclosed within the printed material, with no exposed contact.
Browse weekly pill organizersSpecific caution
- Magnetic round model: if the product ever breaks, keep the magnets away from children and pets; swallowed magnets require immediate medical attention.
- Not intended for liquids or leak-prone gel capsules.
Cleaning and care
- Hand-wash compartments and lids with mild soap.
- Dry thoroughly before use, compartment by compartment.
- Not dishwasher-safe.
Collection
Keychain.
Designed and 3D-printed in PLA. The lid screws on, with no magnets, and a metal keyring is supplied. Compact and lightweight, for one to four pills always on you.
Browse keychain pill holdersSpecific caution
- Small parts: choking hazard if swallowed. Keep out of reach of children and pets.
- It lives on your keys, so it lives in your pocket: check that the lid is screwed on after refilling.
Cleaning and care
- Hand-wash with lukewarm water and mild soap.
- Avoid prolonged soaking; the threads dry best in open air.
- Not dishwasher-safe.
Collection
Hourly.
Made to order, designed and 3D-printed in PETG, the plastic family used for medical trays, with a deliberately translucent lid so a caregiver can check at a glance.
Browse hourly pill organizersGood to know
- PETG tolerates heat better than PLA (softening from about 80 °C), but the same rule applies: no microwave, oven or dishwasher.
- The translucent lid is part of the design: clean it gently to keep it clear.
Cleaning and care
- Hand-wash with lukewarm water and a drop of dish soap. A disinfectant wipe is fine on the PETG case, but never alcohol or solvents on the printed hours.
- Use a soft cloth on the translucent lid, never a scouring pad.
Collection
Artsy.
Original motifs drawn in the studio, designed and 3D-printed in PLA. On most editions the artwork is part of the printed material itself, and each piece arrives in a gift box.
Browse Artsy editionsGood to know
- The motif is printed in the material itself and will not peel or fade with normal use. The exception: editions whose product page specifies a UV-printed motif; treat those like the personalized lids, with no solvents or alcohol-based cleaners on the print.
Cleaning and care
- Rinse gently with lukewarm water and mild soap.
- A soft cloth keeps the relief of the motif clean; avoid abrasive cleaners and scouring pads.
Collection
With your image.
Your photo or logo, UV-printed in high resolution on the outer surface of the lid. The print never contacts the contents.
Browse personalized pill organizersSpecific caution
- The UV print is durable in daily use, but treat it like the face of the object: no solvents, no alcohol-based cleaners on the printed surface.
Cleaning and care
- Clean the printed lid with lukewarm water and mild soap, with a soft cloth.
- The base cleans like any PLA model: lukewarm water and mild soap.
Care questions
The essentials, in four answers.
How do I clean my Biinii Design pill organizer?
Can a Biinii Design pill organizer withstand heat?
Is the printed motif or photo in contact with the pills?
Are Biinii Design pill organizers watertight?
A doubt about your model?
Shipping, returns, customization: the FAQ covers the rest. And for anything else, the studio answers within 24 to 48 working hours.